Update profile
    Change password
    Sign out

Fluorescent Western Blotting

Fluorescent reagents are growing in popularity for Western blotting because they offer increased time savings over chemiluminescent detection and reduced chemical waste compared to both chemiluminescent or chromogenic detection systems. Historically, the instrumentation available for fluorescent detection has not been able to offer the sensitivity required by many researchers or was prohibitively expensive. However, with the advancements in imaging technology, new fluorescent probes and the reduced cost of both, fluorescent detection systems are quickly replacing chromogenic and chemiluminescent detection methods in many laboratories. While the detection limits are still not as low as chemiluminescent detection, fluorescent detection has the unique advantage of allowing multiple targets to be assayed for on the same blot at the same time without the need to strip and reprobed.

Page Contents:

Protein Methods Library Home

Learn more...

Overview of Western Blotting

Chromogenic Western Blots

Chemiluminescent Western Blots

Introduction

Fluorescent blotting applications differ from other detection systems in that the signal is not a product of an enzyme reaction, but rather a transient light emission resulting from the excitation and subsequent release of photons as the excited molecule returns back to its normal state. This is in contrast to enzyme-substrate systems that produce a colored product or light emission as a result of an chemical reaction. This allows optimized fluorescent applications to be more quantitative than enzyme systems.

Similar to enzyme reactions, fluorescent reagents must be optimized for optimal signal:noise ratio. If the the degree of fluorescent labeling is too low, the signal will be weak. However, if the degree of fluorescent labeling is too high, the signal will also be weak due to the inactivation of the detection reagent or quenching of the signal caused by a phenomenon known as Förster resonance energy transfer (FRET).

Another concern unique with fluorescent applications is fluorescent properties of the matrix in which the proteins are immobilized on. As with fluorescence microscopy, care should be taken in choosing both the support for the proteins. Both nitrocellulose and PVDF membranes and acrylamide gels have fluorescent properties which can create a significant amount of background noise that reduces signal:noise ratios in fluorescent blotting applictions.

Learn more...

Fluorescent Probe Selection Guide

Download documents...

Tech Tip #24: Optimize antigen and antibody concentrations for Western blots

Tech Tip #31: Calculate dye:protein (F/P) molar ratios

Data Imaging for Fluorescence

Recording and documenting the results of fluorescence-based Western blotting requires special instrumentation, namely some sort of fluorescence imager. Several manufacturers offer fluorescence imagers, most of which use either filter-based and laser-based technologies to deliver the appropriate excitation wavelength and then record the emission light output. Captured images are saved digitally (see figures on this page).

The number of commercially available fluorescent dyes having different excitation and emission spectra continues to increase. Fluors with non-overlapping spectra enable multiplex analysis, whereby two or three different targets can be detected and independently distinguished in the same lane and blot. However, the imager used must be equipped with the appropriate filters or lasers for the fluors used.

Certain instruments are specialized for detection of infrared and near-infrared fluors, while others provide for analysis of only one or two particular fluors in the visible range. Increasingly, new instruments are being offered with capabilities for detection of nearly any combination of excitation and emission wavelengths.

For additional information about instrumentation, see the links to related product and informational pages in the sidebar.

Learn more...

Ex/Em Spectra: DyLight Fluor Absorption and Emission Spectra

Fluorescent Western blot for Tubulin and TNFalpha using DyLight 680 and Dylight 800 nd imaged with the LI-COR Odyssey.
DyLight 680/800 labeled antibodies used in two-color Western blot. Proteins were separated in 4-20% Precise Protein Gels and transferred to Low-Fluorescence PVDF Transfer Membrane. The membrane was blocked overnight in SEA BLOCK and target proteins were detected following the recommended protocol. Membranes were imaged with the LI-COR Odyssey Infrared Imaging System. Tubulin was detected from the indicated quantity of HeLa cell lysate. Purified TNFα was detected at the indicated quantity.
View products...

DyLight Fluorescent Dyes

DyLight Antibody Labeling Kits

Low-Fluorescence PVDF Transfer Membrane and Filter Paper

Restore Fluorescent Western Blot
Stripping Buffer

Molecular Weight Markers for Fluorescent Detection

For detection of any Western blot, it is desirable to use prestained molecular weight markers that are transferred to the membrane along with the protein sample. The appearance of the molecular weight markers on the membrane allows estimation of molecular weights for any protein bands that are detected as well as effective separation of the proteins of interest in the gel prior to the transfer step. When chemiluminescent detection is used for Western blotting, protein bands are detected on film or with digital imaging equipment. Unless modified, molecular weight markers do not show up on during fluorescent imaging since they do not produce any signal. Therefore the use of fluorescently tagged molecular weight markers is advantageous.

Although the dyes used to make prestained molecular weight markers have some fluorescent properties, protein molecular weight markers that are labeled with fluorophores provide better signal:noise ratios. The Thermo Scientific PageRuler Prestained NIR Protein Ladder is a mixture of 10 proteins (11 to 250KDa) that are blue-stained and fluor-labeled for near-IR fluorescent visualization and protein sizing following electrophoresis. The protein MW markers in this ladder resolve into as sharp bands when analyzed by SDS-PAGE and are labeled with a fluorescent dye for visualization with instruments equipped for detection of near-infrared (NIR) fluorescence. These include Typhoon* Imagers and the LI-COR Odyssey* Infrared Imaging System.

View products...

PageRuler Prestained NIR Protein Ladder


Written and/or reviewed by Douglas Hayworth, Ph.D.

Instructions | MSDS | CofA
Product Instructions | MSDS | CofA  

Recommend this page

Follow Us
Email Sign-up  Email Announcements

 



Antibodies  |   Molecular Biology   |   Cell Biology   |  Thermo Scientific  |   * Trademarks  |   Privacy Statement
© 2014 Thermo Fisher Scientific Inc.   |   3747 N Meridian Rd, Rockford, IL USA 61101   |   1-800-874-3723  or  815-968-0747